Updated November 2026
BMW Valve Cover Gasket Replacement Cost: $420-$1,233
BMW is one of the most expensive brands for this repair, but the range is wide. An older inline-6 with a conventional gasket is $420-$611 on RepairPal's 325i estimate. A turbo engine with an integrated plastic cover runs $656-$1,233, topped by the X5 at $869-$1,233, and most of that is labor.
Older inline-6 (M54 / N52)
$420-$611
Conventional gasket, 325i (RepairPal)
Turbo, integrated cover (N20 / N55 / B58)
$656-$1,233
Turbo models, 328i to X5 (RepairPal)
BMW Valve Cover Gasket Cost by Model
Ranges below are RepairPal national-average estimates (parts and labor, before tax). Your quote will vary with location, whether the shop is a dealer or independent BMW specialist, and whether the plastic cover needs replacing as well as the gasket.
| Model | Engine | Cost Range | Cover Type | DIY |
|---|---|---|---|---|
| BMW 325i (E46 / E90) | M54 / N52 inline-6 | $420-$611 | Conventional | Moderate |
| BMW 328i | N20 turbo-4 / N52 inline-6 | $656-$924 | Integrated (N20) | Hard |
| BMW 535i | N54 / N55 turbo inline-6 | $678-$964 | Integrated | Shop only |
| BMW X3 | N20 / B48 turbo-4 | $795-$1,130 | Integrated | Shop only |
| BMW X5 | N55 inline-6 / N63 V8 (all engines) | $869-$1,233 | Integrated | Shop only |
| BMW 335i | N54 / N55 turbo inline-6 | $772-$1,119 | Integrated | Shop only |
RepairPal Fair Price Estimator, national averages, all six models re-read 15 November 2026. Ranges exclude tax and shop fees. The X5 figure is RepairPal's model-wide average across X5 engines; RepairPal does not split it by engine, and an X5 50i with the N63 twin-turbo V8 has two integrated covers, so expect a quote toward the top of the range or above it.
BMW 328i Valve Cover Gasket Cost by Year
The 328i is the most-searched BMW for this repair, and the cost depends on the year because the engine changed with the generation. A 2007-2011 E90 328i uses the naturally-aspirated N52 inline-6 and is the cheaper of the two. A 2012-2016 F30 328i uses the turbocharged N20 four-cylinder with an integrated plastic cover, which costs more. The 2013 model year overlapped both engines, so check which one you have.
| Year / Chassis | Engine | Cover | Cost Range |
|---|---|---|---|
| 2007-2011 (E90 / E92) | N52 / N51 naturally-aspirated inline-6 | Plastic cover, gasket serviced separately | $420-$611 |
| 2012-2016 (F30) | N20 turbocharged 2.0L four-cylinder | Integrated plastic cover with built-in PCV | $656-$924 |
Engine applications per BMW N52/N51 and N20 328i service data. Dollar ranges reuse the inline-6 and turbo tiers in the table above (RepairPal, re-read 15 November 2026); a 2013 328i can carry either engine.
Why One BMW Costs $420 and Another Over $1,200
Conventional cover (cheaper)
Older naturally-aspirated inline-6 engines (M54 in the E46 325i, N52 in the E90 325i/328i) use an aluminium or magnesium valve cover with a separate rubber gasket. When it leaks you clean the surface and fit a new gasket: RepairPal's 325i estimate has $58-$80 in parts and $362-$531 in labor, a total of $420-$611, because the cover itself is reused.
Integrated cover (pricier)
Turbocharged engines (N20, N26, N55, B48, B58, N63) use a plastic valve cover with the crankcase-ventilation diaphragm and oil separator built in. The plastic warps and cracks with heat cycling, so a leak often means a complete cover assembly rather than just a gasket. RepairPal's estimates for these models run $656-$1,233, almost all of it labor; if the cover is replaced, its price is added to that.
Which BMW Engines Are Known for Valve Cover Leaks
Valve cover and cover-gasket failure is one of the most common oil leaks across the modern BMW range. The usual culprits:
- N20 / N26 (2.0T): 328i, 320i, X1, X3, 528i. The plastic cover and integrated PCV are a frequent leak point from around 60,000-90,000 miles.
- N54 / N55 (3.0T): 335i, 535i, X5 35i. Cover-gasket and PCV seepage is common; oil often appears down the back of the engine.
- N63 (4.4 twin-turbo V8): X5, X6, 550i, 750i. Two integrated covers in a hot, tight valley make this the most expensive version of the job.
- M54 / N52 (older inline-6): 325i, 328i, 525i, Z4. Conventional gasket leaks here are cheaper to fix but very common with age.
Signs Your BMW Valve Cover Gasket Is Leaking
- Burning-oil smell after driving, especially at stops
- Oil pooling in the spark plug wells (can cause misfires)
- Visible oil down the side or back of the engine
- Smoke from the engine bay when oil hits the exhaust manifold
- Low oil level between services with no obvious puddle
- Rough idle or a stored misfire code on N20/N55 engines
On turbo engines, a leaking valve cover often goes hand in hand with a failing PCV diaphragm, which is one reason shops replace the whole cover. See the full leak symptoms guide.
Cost by Vehicle
Compare BMW against 21 other popular vehicles.
Audi Cost by Model
The other European brand with integrated covers.
Cost by Engine Type
Why European integrated covers cost the most.
Dealer vs. Independent
A BMW specialist often beats the dealer rate.
Cost Overview
General cost breakdown and calculator.
BMW Valve Cover Gasket FAQ
How much does a valve cover gasket cost for a 2008 BMW 328i vs a 2013 328i?
It depends on the engine, which changed with the generation. A 2007-2011 E90 328i uses the N52 naturally-aspirated inline-6 and runs about $420-$611, the RepairPal 325i range, because the gasket is serviced separately from the cover. A 2012-2016 F30 328i uses the N20 turbocharged four-cylinder with an integrated plastic cover, so it runs about $656-$924, the RepairPal 328i range. The 2013 model year overlapped both engines, so confirm whether your car has the inline-6 (N52) or the turbo-4 (N20).
How much does a BMW valve cover gasket replacement cost?
Between $420 and $1,233 on RepairPal's national averages, depending on the model and engine. Older inline-6 BMWs with a conventional valve cover (like the M54/N52 325i) run $420-$611. Models with turbo engines and an integrated plastic cover (N20, N55, B58, N63) run $656-$1,233. Most of that is labor: RepairPal puts parts at $96-$103 on the 328i and $98-$102 on the X5, so if the shop also replaces the plastic cover, the cover price comes on top.
Why is a BMW valve cover gasket so expensive compared to a Honda?
Mostly labor. RepairPal's X5 estimate is $771-$1,131 in labor against $98-$102 in parts, and its 328i estimate $560-$821 in labor against $96-$103 in parts: packaging, charge piping and the integrated crankcase-ventilation system make the job longer. On turbo engines where the plastic cover itself has warped or cracked, shops replace the whole cover, which adds its price to the bill.
Is it the gasket or the whole valve cover that fails on a BMW?
On older M54/N52 engines it is usually just the rubber gasket. On turbocharged N20, N26, N55, B48, B58 and N63 engines the plastic cover itself warps or cracks around the integrated PCV diaphragm, so most shops replace the complete cover and gasket as one job.
Can I replace a BMW valve cover gasket myself?
On an older inline-6 with a conventional cover it is a moderate DIY job. On the turbo engines it is harder: charge piping and the integrated PCV system make it a shop job for most owners, and the plastic cover bolts must be torqued to spec to avoid cracking.
Model cost ranges: RepairPal Fair Price Estimator, BMW 325i / 328i / 335i / 535i / X3 / X5 valve cover gasket replacement (national averages, re-read 15 November 2026). Engine-code applications and failure patterns reflect common BMW service experience.